Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I wanted to test nrf51-ble-driver_linux_0.5.0 in the latest Ubuntu, but got this problem:
...
OSError: libboost_thread.so.1.54.0: cannot open shared object file: No such...
Is this even possible? I have a BLE connection with an interval of 7.5 ms. I've set up a radio notification with a distance of 2680us in order to be able to transmit 4 BLE...
Hi,
I want to know how sd_ble_gap_authenticate api works.After executing this api, what are the events invoked at peripheral end. Is there any event that blocks CPU or...
We are designing product based on nrf2401A
The problem that we encountered was that the nrf2401A forgeted configuration data, was it possible ?
we use our product in highly...
Hi,
I am using the nrf51822 in an intermittent high-current application where if the battery is close to dead, will sometimes cause the chip to reset because the voltage...
I am using SDK 8.1.0 and Eclipse on a Mac. I am having difficulty flashing my app that uses the nRF51 sdk onto nRF51. I am using JLink
I assume I need to flash two things...
Hi nrf51 developers,
I'm developing multiprotocol application by combining BLE and a proprietary protocol. I'm using concurrent multiprotocol timeslots API. Started with...
I am new to programming both the nRF518122 as well as the Cortex-m0. As I have been building and running the example apps that come with the nrf51 sdk, I run across the CMSIS...
Hello,
I'm developing device application where I need:
peripheral (advertising also when in connection)
central role
whitelisted connections
maybe some encryption...
Hello,
I'm trying to do some simple printfs to hyerperterminal as a way to debug my code. I have used the uart example init code but nothing prints:
void init_uart(void...
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I have a nRF51DK. The Softdevice on the board is S110.
I load the ble_app_template from the SDK 8.1 on the chip. It builds with success. Now with the MCP I am able to see...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
