I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi,
Question 1: Why nRF52832 not supporting Thread? Is it because Memory? Hardware?
Question 2: Can you advise what is the advantages or applications to use BLE+Thread...
Hi,
I'm sorry but i cannot find in the discussion the definition of this structure NRF_SPIM_Type
it is not defined in nrf_spim.h
typedef struct { NRF_SPIM_Type * p_reg;...
Hi,
We are looking for an industrial solution to program our NRF52832 on a custom board, until now we are using the programming chip directly from the NRF52DK, it works...
My custom board with NRF52810 is done and I'm now trying to get some examples working. I am adapting blinky_s132 in SES. To do this I edited the project options including...
i'm new to this board can you find some course for this board
from scratch the courses will be very helpful
just the video tutorials are very advanced
the documentations...
Hi folks,
I am working on ble_app_uart example program nRF52 SDK 15.2 Verion , in this case i am writing the data in flash for future use , Now i am to get the specific...
Hi Team,
We are using nRF52840 DK with sensors. We developed a custom code that is working fine. But the issue is current consumption. Showing below the readings.
The...
I have taken the code found here:
https://github.com/bjornspockeli/custom_ble_service_example
and modified it so that the custom characteristic is located in user memory...
Hi,
Good day!
I tried to add the RTC2 driver to our application and i keep getting this compiler error message (using sdk16.0).
Here is my sdk_config.h. Not sure why...
Hi
I'm planning to connect three different BLE peripheral like Heart-rate sensors, Health Thermometer, and Blood Pressure to a Central BLE device.
I'm using a small customized...
Hello
What is the specified max current on the supply pins for nRF52840?
The GPIO pins are specified to source max 14mA in 'high drive' mode:
How many of these pins...
Got called back to an old product that used nRF24LE1. Need to do a simple hot fix.
But I don't have the nRF6700 Dev Kit with me anymore. It cost almost $600 to get one from...
To the kind attention of Nordic support team,
I know that gazell secured libraries are available at least for keil compiler and nRF52840 device.
Are those libraries available...
Hi,
We are seeing a voltage of approx 1 volt on our USB connector when USB is not being used (VBUS).
We are using our device in a Wet environment; this voltage between...
Hello,
I am using nrf52840DK and I try to send data from sensor to ble toolbox. I want it to advertise for 1 minute and then go sleep for 5 minutes and do it again and again...