void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
HI:
i use master control panel to write data to 51822(sdk8.0 ble_app_uart),but i can't write successfully.i do as help information.and i have selected the right UUID and...
I've just got up and running with the nRF51 DK. I've had a play with some of the examples, and now I've started on my own project using ble_app_template_s110_pca10028 as a...
After startup, I was able to send a spi msg from the master (app chip) to the slave(nordic). But when I try to sent the second message, I did not get any response from the...
I am using the SPI Slave peripheral and attempting to send the nrf51822 bytes from another MCU.
Am I right to assume that there is, basically, a 256 byte max per transaction...
Hi,
I have nRF51822 board which works great with my app when running on iOS 7
The application listens for iBeacon transmission and displays them.
When i installed my...
Hi, I made a custom PCB.
I use a Revision 2 MCU.
The antenna is printed. I didn't used the chip antenna.
Sorry for not showing both the full schematic and the...
Dear all,
I'm trying to connect the NRF51-DK (PCA10028) with a LSM330DLC accelerometer over TWI (I2C). I'm using the ble_app_uart example, included the twi_master.h file...
I need to implement a function to store some parameters such as uart baud rate and use these parameter for device initialization, The parameter could be modified when the...
Hello,
I`ve got a working S120 peripheral BLE device with custom services and characteristics.
I am able to connect and bond with iOS and Android. But I cannot connect...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
My nRF51 will occasionally lose connection to the computer, and I have to disconnect and then reconnect it before it will work. How can I reset the device dynamically, without...
I'm trying to compile a project I have for nrf51 on nrf52. I am running into errors with macros not being set.
For example:
error: #20: identifier "ADC_CONFIG_RES_10bit...
Hi,
I'm working on a sensor application that sends out fairly large quantities of data via BLE notifications. I understand how bluetooth works and have read and followed...
