Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I have troubles programming my blinky in a nRF51DK. I have S110 v8 loaded and can flash blinky with nrfStudio. Not with GDB. It seems that the flash is not erased. After...
Hi to all,
I've started a new ble_apps_lbs project from ble_app_template. I've an nRF51822 chip with S110 already programmed, I modify the settings for the target cpu, and...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi, After i flashed the firmware MEFW nRF58122 0.11.0, MCP "start discovery" button is disabled. I flashed the lower version MEFW nRF58122 0.9.0. Same issue.
There is exception...
Dear all,
I have a question on the LFCLK accuracy in the smart beacon kit, which is pca20006.
When I see the specification of LFCLK crystal 32.768kHz, this crystal has...
I'm developing a product using a module with a built-in NRF51822 and I'm experiencing a strange error:
After staying in a connection for a long time (hours to days), the...
Hi, I'm making a product with the nRF51822 chip.
I was looking at the MFi.
As you see in the picture, the condition for not taking the MFi is like this.
At the...
Hi, I've written my own ACI code for an arm cortex M3. So far, everything is working fine. However, I've noticed that if all data credits are used up and a DisconnectedEvent...
I'm using nRF51822 SoC and i want to notify the Androïd(4.3) application with the changes of the Major value due to switching the beacon mode . How to change Major value ...
Hi,
i can say that i'm familiarized with nrf51 devices from some time ago.
Using softdevice 7.1.0 and MCP 3.7.1 i was able to perform a device firmware upgrade using just...
Hey I am working on nordic nRF51822, I have a doubt.
Basically I want to use it as an iBeacon and along the iBeacon payload I also want to send some services.
Is that fundamentally...
Hello,
I tried to get the bootloader dfu example with the S110 8.0 and the latest 8.0.0 SDK running but ran into tons of issues. The packet handling with KEIL is just insane...
Hello everyone!
I'm writing here becouse I'm quite new to the embedded world and I'm experiencing some troubles starting with this platform.. I must say that, since I found...
Hello,
In my application, I'm going to power the custom board with a fixed 5V connection. What is the best practice for powering the nRF51422 IC? I was thinking in using...
