I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
I develop my BLE with SDK 8.1 and softdevice 8.0, and I want to restore some data(about 50 bytes) to flash, can anyone please help to provide me an example for the entire...
I have had a look at you experimental implementation of DFU signing.
I'm very concerned about the code size. The old Bootloader used about 13KB and the new one with signing...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
I've got 4 services with 15 characteristics between them. Trying to add any more than that results in sd_ble_gatts_characteristic_add() returning NRF_ERROR_NO_MEM .
All...
Hi Expert,
I found a weird case that at my 51822 plaform with s110 enabled, if I define a global buffer like:
static uint8_t system_buffer[1024];
it obviously will...
Hi
The nRF24Le1 has 256 bytes in the infoPage for user data, starting 0x0100.
My question is how to write to that area?
Is it accessible from nRFgo Studio?
Is it accessible...
Hi every body,
Is there any way to increase the support packet per connection to more than 1 packet for S120 softdevice if i have just single slave and single master? ...
HI,
I have followed all the steps from devzone.nordicsemi.com/.../ and I can relay text between Termite & my iphone.
Can someone share a function / method which I can...
Hi,
I used the ancs demo of nRF51_SDK_7.2.0_cf547b5 to modify our application. It still work well, but sometime when I left the device and went out with my Iphone about several...
Hi,
I have two customs boards and on the one with the QFABA0 I can go to system off and see 0.6uA of consunption but on another board with the QFABB0 I go into system off...
