Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I’m writing BLE UART code. When BLE is not connected, current consumption is ~30 µA. But when BLE is connected, consumption increases by ~1 mA. I want to reduce the current...
Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi, I have an Adafruit Feather52 board which is preloaded with a serial DFU bootloader and the S132 Softdevice, of which I also have the merged Hex file. I would just like...
Hi,
I am designing a custom PCB using the nRF51422 chip. I have a program that I developed on the nRF51-DK. The program reads the capacitance value of a proximity sensor...
Hi All,
i need some helps. I need a device that can connect with one phone only, so i have created a whitelist wih size of 1.
During the life of device the device can...
Hello, I'm pretty sure the new BLE 5 will come out soon and it will integrate the mesh. And if mesh needs to be done at a protocol level, it must be the softdevice.
So...
Hello iam using softdevice 110 and SDK 10.0.0, i have implimented dfu in my project, i want to update a region in EEPROM by calling pstorage_update() function before calling...
A while ago I asked this question devzone.nordicsemi.com/.../.
Yesterday I re-installed MDK 8.11 after a computer crash and I had IAR version 7.60.1 and version 8.11.2...
Hi,
I need to design a small nRF52 board On 24mm Dia 2-layer PCB, same like nRF51822 Bluetooth Smart Beacon Kit (nRF51822 Coin-Cell design). Please find the attached Schematics...
Hi everybody.
I encountered issues with the formentioned setup. In my project I'm using latest SDK 13.1, softdevice S132 v.4.0.2. I'm compiling the project with latest...
Hi to everybody,
I am working with a custom board based on the nrf52832, while trying to integrate to my existing application the DFU functionality I am having problems...
I am trying to measure the ADC on all 8 ADC pins of the nRF52 on the PCA10040. I'm noticing quite large amount on noise on floating lines (up to 0.6V). However my biggest...
We have a device with a main MCU connected to a NRF52832 for BLE communication. Our device have Battery, Heartrate and a custom service. The first implementation used a Sparkfun...
I am trying to decide what Nordic solutions would best support the application throughput requirements seen below. Distance requirements are low (1 meter each link).
...
Hi there,
I have nRF52840-Preview-DK eval board. I have downloaded the “SDK 13.1.0”. I was trying out the power management example under the folder “..\nRF5-SDK_copy\nRF5...
