I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Is there a UART bootloader available for nRF52840? Doesn't have to be secure.
Already searched in SDK 12.2 and 13 alpha, with no success.
Thanks for your help!
I installed the latest JFlash (6.12d) from Segger's site, and it updated the JLink firmware.
However when I try to program the hex files downloaded from www.nordicsemi...
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL does not set the .burst field in the nrf_saadc_channel_config_t structure.
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE...
The app_fifo support e.g. in SDK 12.1.0, appears to have a serious problem when the read_pos/write_pos values wrap. i.e. when the fifo has been used over a period of time...
I have BLE400 extended board for nrf5. It has cp2102 on board from Silicon Labs. I installed drivers for mac and can see NRF_LOG_INFO via terminal. It would be great to have...
i am using nrf52840 with sdk 13.0.0-1.alpha. I want to boot the application from bootloader but by
using UART as a transport layer.
Would you plz help me?
I found end of address of fstorage from macro of "#define FS_PAGE_END_ADDR (fs_flash_page_end_addr())". But I want to change the start address of fstorage. Which macro or...
I have multiple GPIOs that are configured to use GPIOTE in my application. When one of these GPIOs is in the active state I start timer. Once the timer expires I want to enter...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to work with VL53l0x distance sensor. Basic communication working good, but i am not able to get distance...
Hello
I tested a BMD-300 Module and Nordic Team has been very helpful.
I tried to reach the maximum speed in this module.
I like to send 4x20 byte per 30 ms, but I...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
I've been through the tutorial of connecting the NRD52 board to my PC, but my PC isnt recognizing it at all. No pop up for any usb devices. I've tried different cables and...
Dear Nordic Team,
Thanks for supporting.
currently i am try to interface MMA8453 accelerator with ble proximitty example .Already i have interfaced peripheral example...
