Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...
To enable comparability with an existing client, I'm attempting to configure the nRF51822 to provide a GAP service that includes user description descriptors (UUID 0x2901...
I'm trying to store some values with fstorage. The store operations seem to be queued successfully, but never executed. I currently have this to test the behavior:
FS_REGISTER_CFG...
Hallo everyone,
I am reciving a notification from my server, which lenght can be 8, 20, 30 bytes but when I want to display the info using NRF_LOG_INFO is not printing...
To All,
From reading the datasheet I understand that nfr52832 spi can only send/receive up to 255 bytes at once. And to work around this a list method is used.
Because...
Hi,
I’m working on a device that requires to enable the softdevice when connecting with a smartphone via Bluetooth and disable it when acquiring data from an analog source...
Hello,
I am using sdk12 and uart code. I want to send my sensor data readings to ble app. For that I have modified the ble_app_uart code and I am able to send 8 packets of...
Hi all,
In my project I have a structure its length was about 2KB, I'm saving it as a static variable after using this I come across with a weird behavior from the board...
Greetings,
I'm having trouble being able to perform a DFU with the secure serial DFU. My setup:
Using PCA10040 (nRF52832) with the s132_nrf52_4.0.2_softdevice.hex...
Hi.
I am using saadc sample cod of SDK13. Changing some parameters based on the analog input, the example is sucking somewhere where I have not been able to find it.
...
Dear all,
I am facing small problems, which I guess most of you faced at some moment.
I am trying to switch from working with ST microcontrollers to working with nRF52...
Hi,
I know that the default handle value of device name is 3, but in my application i am not getting the default device name handle, is it possible to change the device...
I want to save precious CPU cycles by writing 40 i2c (TWI) registers in one shot. Can I somehow set up the TWI master to write 40 registers (each 16-byte address with 8-bit...
What is the maximum length of pdu for ble advertisement? I have ported the example application of solar powered beacon without softdevice.
I just wanted to know if it was...
