Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi ,
I need the BLE peripheral to have 'name1' at the start up and change it to 'name2' when a button is pressed. I want to do this without disabling and enabling the softdevice...
Hello,
I'm in the process of updating our codebase to SDK 14 and am facing some problems getting the CLI to work. My goal is to get CLI and logging to output on the same...
[nRF52840 + SDK13]
On the hardware that I have, the UART driver is hitting a communication error because the RX line is low. This only happens when the UART lines are disconnected...
Hello,
I try to achieve maximum data throughput using pc-ble-driver 1.0 and nRF51(with ble_connectivity) as BLE dongle.
First problem I encountered was the bug with...
Hi,
we are currently testing the nRF52 DK as a reciever for several BLE devices.
For a fist test we implemented some datarate measuring in the:
PC -> nrf Connect -...
Hello,
I am using ndk52 (nrf52832) as peripheral and central in my system. I did some changes on ble-app-uart example for both. Now i can send my packets continiously....
Hello,
I am using ndk52 (nrf52832) as peripheral and central in my system. I did some changes on ble-app-uart example for both. Now i can send my packets continiously....
Hello,
I was wondering what is the best example to take as reference in case I want to pair two BLE devices automatically, I mean, I would like to make my devices to start...
i use RTC wakeup the sleep mode,project used the uart etc.
uart baudrate set to >=115200 sleep mode normally.but is baudrate set to <115200 sleep mode at 50ms+- periodic...
I am trying to use nRF connect's advertiser feature to simulate some sensor output for my testing. The sensors use BLE advertisements with scan response to send out data....
Hello community,
I am working in a central device with SDK 13 v. 4, PCA10400 (NRF52832) and SD 132 and one task is to receive 30 bytes from a sensors as a notifcation,...
Hi,
we are using are more or less unmodified version of the Secure DFU bootloader example. Especially all BLE/Softdevice configuration in "libraries/bootloader/ble_dfu...
As mentioned here , my poor little Thingy:52 doesn't work after upgrading to version 1.1.0 through the iOS app.
After getting my Thingy:52 i played arround with it for...
I try to add function for the peer manager initialization and set the security parameters. I did not understand keypress and lesc parameters exactly. Documentation says for...
