Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am working with the nRF52 DK, using SDK v14.2.0 and SoftDevice S132.
After removing all BSP functions from the BLE UART example, I am setting up LED1 and LED2 of the...
Hello,
I'm trying to get the FDS to work, but it's giving me a headache. I'm using SDK 13.1 and S132 4.0.2 on a NRF52832.
In the beginning I thought I had that issue...
Hello,
I am trying to figure out my problem related to this question .
I am writing just a couple of words to flash with FDS. The problem is that after writing, the...
I am trying to use nfc_t4t_lib in NFC_T4T_EMUMODE_PICC mode. After receiving an APDU I am doing some calculations and sending reply with nfc_t4t_response_pdu_send. If calculations...
What is the best way to store the values of my attribute data?
With my current code, from the tutorials, the read, write and notify works fine.
But I need to store the data...
Hello
I noticed that since S132 v3.x.x we can configure the MTU. Does all the posts referring to long writes in this forum apply to the situation before this feature ?...
Hi
on nrf52832 ble_app_uart how can change MTU size and LL payload size?
have any source ? or example ?
or any change MTU and payload example ?
( for BT4.2 ~ BT4...
Hi,
I'm using SDKv14.1 on nRF52810. I doing the DFU according to the ble_app_buttonless_dfu example. When I use sd_ble_gatts_service_add to add service UUID in the ble_dfu_buttonless_init...
By testing the source example of throughput example of S132, it is known that throughput is mainly affected by four factors.
1, ATT_MTU
2, DLE
3, Connection event...
Hi Nordic team,
Currently our company under developing the product using NRF52840 + S140 Softdevice.
Now we prepare to list our product with Bluetooth SIG but after...
Hi,i have some problems at fds in sdk14.1 ble_app_buttonless project.
1,fds_register() & fds_init();
2,fds_record_write();
3,fds_record_find();
4,printf the record...
Hi guys,
Right now, I'm trying to do some throughput measurements via the experimental ble_app_att_mtu_throughput example. This using the SDK 14.2 and S132 on two nRF52832...
Hi,
I have seen some curious behavior with the FDS module. I'm using nRF5SDK 14.2.0 with s140_nrf52840_5.0.0-2.alpha, with FreeRTOS. In short: In some cases it seems that...
Hi!
I want to get infinite advertising.
My advertising gets timed out in 180 sec.
I have set to Fast Advertising Mode.
Below is my code
static void ble_evt_dispatch...
