Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I'm having issues with my application implementing DFU. I added the DFU service in my application and can get into the bootloader. I have added my own key to the bootloader...
I'm migrating form S332 0.9.1alpha (aligned to S132 2.0.0) to the newer S332 2.0.1 (aligned to S132 3.0.0) on a nRF52 board, and I'm seeing a new characteristic under Generic...
Hello,
I am trying to configure gpiote to give an interrupt for wake on motion functionality in MPU9250
I am configuring the MPU for that by calling separate wake_on_motion...
I tried to run some examples from pc_ble_driver_py but i always end up with the following exception.
(using python 2.7.9)
Traceback (most recent call last):
File ...
I have an application developed using S110 v7.3.
I want to upgrade to v8.0 to get additional features (over air update, DC/DC converter etc.), but notice S110 is not supported...
I have bootloader that supports Serial(HCI) DFU on the nrf52832 device which I have to update to Bootloader that supports OTA DFU and also a new application firmware. I tried...
Hi,
When trying to update an app using Secure DFU, we get invalid object error. The error comes from dfu_decode_command.
Using nRF5 SDK 12.2.0 on custom nRF51822 board...
I have followed the CoAP example from IoT SDK,
I have a Raspberry PI set up as the router,
and two nRF52 boards, one is the client, the other is the server.
Following...
I have following questions:
Is there an example for implementing WeChat on a nRF52?
Is the nRF52 module supported for WeChat AirSync?
Where can i finde the requirements...
Hello!
I'm drawing a circuit with nrf52840 chip and I want to ask some questions:
Is it ok to use 2-side pcb (not 4)? what's of these better in part of radio communication...
Hi, I use nrf connect to programing demo board nrf51 dongle to get it work, failed.
error log as follows:
2017-03-02T09:30:20.014Z INFO Application data folder: C:\Users...
Hi,
Does the PPI module automatically clear the event flags for the linked event? For example, if I have the following:
NRF_PPI->CH[0].EEP = (uint32_t)&(NRF_GPIOTE->EVENTS_IN...
hi
I'm porting Arduino code which has calls to ShiftIn() to read a byte from a GPIO Pin and bitWrite() to write a bit into a byte variable at a particular position.
Below...
