Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I'm using nRF52DK and SDK12.2.0.
Trying to change MTU size.
When I modified app_nrf_uart example as below
#define NRF_BLE_MAX_MTU_SIZE 103
Then infinite reboot...
I am working on a project and have successfully implemented single channel PWM to dim leds (using a transistor FET).
The pwm init code is below:
uint32_t err_code;
nrf_drv_pwm_config_t...
image description (http://)when i try to flash the led binky programme to nRF51822 Ek. i am getting device error and LED also glowing continuously.
1.this device error was...
So I was thinking of having the following:
nRF24L01+
to balun (e.g., Johanson 2450BM14A0002 or Anaren BD2425NnRF)
to PA/LNA RFX2401C
to PCB antenna
If...
Hi all,
I want to clarify are there any deference between "connection_id" and "conn_handle" ?
I use a multilink central application with 8 possible peripherals devices...
Hello,
I have some difficulties to make an ant acknoledgement with my nrf51422 (s210), and i would be grateful if you could help me with it. (SDK used 12.2)
I have 2...
Please give me info about configuring a timer at given timeout. For eg,. if we want to blink LED for 30 seconds, how to configure them using timer events.
What is the optimum reset strategy for Debugging the nRF52832 with a Segger J-Link Plus?
(Setting of Project_Options/Category:J-Link_J-Trace/Reset)
nRF shall not...
Hi,
I am using SD 120 Ver 2.1.0 and SDK 8. I am getting disconnection with reason 0x3E sometimes. After disconnection even master is scanning, It wont get connected with...
I've been working on a separate problem with the NFC Type 4 library when I ran across this. I can duplicate it in the experimental_writeable_ndef_msg example.
All I did...
Hi Nordic Forum!
I've been trying to run a test program (pin toggle) on a custom nRF52832 board.
First, I tried the same program on the HDK to toggle pin P0.17 (LED1...
When I use additional VS UUID, should I use sd_ble_uuid_vs_add(), se_ble_gatts_service_add() in order?
example,
sd_ble_uuid_vs_add(); <- VS1 UUID
se_ble_gatts_service_add...
