I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Certainly! Here’s a clear, natural English version of your email:
Dear Specialist,
I would like to better understand the two variables used in the SDK for calculating...
I added a few custom services the ble_app_hrs code. I tried to flash the code, it was successful, the device is advertising but not connecting in the nRF connect app. What...
hi,
i started a project based on the ble_app_uart_c example and i have a working connection with a central and a peripheral board. now i'd like to have two peripherals...
Hi fellows,
I'm trying to control accurate/deterministic timing of the first bit from MOSI PIN of SPIM, employing EasyDMA.
According to Figure 69 SPI master with EsayDMA...
Hello,
I noticed the linker file we were using was for the nRF52832_xxAA so I got the nrf52832_xxab.icf from C:\Program Files (x86)\IAR Systems\Embedded Workbench 8.0\arm...
Hello,
I need to add firmware update process via air to my NRF 51822 device that runs application code on stack 12.2. How can i achieve this?
Do i need to add...
Hello,
I want to develop small modules with smart BLE that only sends advertise every 2seconds.
Do you think that the Central module can see all peripherals if the installation...
Hej, I just spent plenty of time finding an answer on above error within here with no luck. Since
there are certainly others facing this problem, I hereby post my solution...
sdkconfig.txt mainc.txt (/attachment/6fb97103178e9eb2c30302351e63ce8f)Can you please tell whether i follow the the entire tutorial as in the link or just the first step for...
Hello, when invoking sd_ble_gatts_hvx, it returned NRF_ERROR_INVALID_STATE (0x00000008), I wanna know what are the list of possible errors, here are a list I made:
CCCD...
Ciao all,
Two weeks ago I have started to learn about beacons and their usage. I have bought pca10040 development kit and designed custom nRF52832 based beacons. After...
Hi,
I've just hit a strange issue with SDK 12.1 on nRF52832.
Usually on BLE_GAP_EVT_DISCONNECTED , sd_ble_gap_adv_start gets called to start advertising and everything...
I am new to nRF 52. Previously i have worked on arduino IDE for programming arduino uno,mega. I have also used MPlabX for programming PIC(MircoChip) series micro-controllers...
Hi,
For the NRF52832, I read that a number of write (per block) is limited before a forced erase of the page. Apparently, the amount of write is 181 times for a block of...
My sensor app is based on nRF UART service and my current case in one sensor (peripheral) one gateway (central).
In a situation where there are two pairs of sensors (S1...
