Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
This omission leads to linker errors:
_build/app/nrf_ble_gatts_c.c.o: In function `nrf_ble_gatts_c_on_db_disc_evt':
nRF5_SDK/components/ble/ble_services/experimental_gatts_c...
Hi All,
We are working on nRF52832 custom PCB design. We are having a small concern for shielding. Do we need to provide shielding for nRF52832 based boards for FCC certification...
Hello,
I am trying to understand a bit better BLE throughtput in order to use it for my application, having read this Nordic Blog , this post and ATT_MTU Throughput Example...
Hi!
I have adapted the heart rate example to have just one service and one characteristic. Initializing works fine and I can read the initial value of 0x00 using my cell...
Hi all,
i have a question about the communication client and server.
I'm using for my project a nrf52 and softdevice s132 v2.0.0, reading the datasheet i can understood...
Hello
we have a projekt with periperal "ble-app-blinky" und central "ble_app_blinky_c".
how to do:
when the "peripheral" battery is below 2.3V
then the led 4 on "central...
I'm trying to regularly change some advertising parameters ( ble_gap_adv_params_t.type ). The only way i can see to do so, is by stopping and starting advertising.
However...
I made a pulse oximeter product with nrf51822AC(base on SDK5.2.0 & S110 6.0.0), and implemented SIG GATT-based profile（PLXP+PLXS). Now we want to do BQB RF PHY testing to...
I have an example combining BLE, UART and SPI in which I use RTT to watch the startup process.
The SoC is nRF52 (BLE Nano2); building with armgcc.
This works ok when JLink...
Hi,
I need to send large data(about 200KB) from android phone to my custom board.
Connected like this :
Android Phone ->(BLE) -> nRF51822 ->(UART) -> Custom board...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
I'm trying to create a program that takes a stream of UART data at 115k baud streaming in and sends it over BLE as fast as possible. So far, I've
(1)Verified/ made some...
Dear Nordics,
If I add ble_nus service to buttonless_dfu example , it will reset after ble_dfu_init(). If I set
*p_ble_enable_params->common_enable_params.vs_uuid_count...
