Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am planning to design BLE MESH based LED lighting system.
(control involved LED ON/OFF , varying two PWMs to control intensity for warm & cold LED drivers, etc)
For...
today simple test ble_nus_string_send time-consuming function, but found that the implementation of a ble_nus_string_send and wait for the success of transmission time-consuming...
Hi, I have a problem with BLE connection. When I bond to the device and then connect, everything works and connection is stable. When I kill the app and try to connect again...
Hai team,
Iam using ble_app_beacon application in nrF51822 dongle .I want to change tx power for every advertising.
example :let us assume frequency 4 for advertising...
I am trying to perform LESC on two nRF52 central and peripheral without bonding is it possible? and how?
My devices does not have I/O capabilities or have any display....
Most examples, tutorials, and standard BLE service implementations within the SDK (14.1.0) seem to use the BLE SoftDevice's sd_ble_gatts_characteristic_add() when adding a...
Hi,
I know that this question has been asked before but it seems like the answers are pretty old.
I have a need to scan on one channel only to receive advertisements...
Hi,
As mentioned in this post:
devzone.nordicsemi.com/.../
the struct ble_gap_adv_params_t --> ble_gap_adv_ch_mask_t give the option to turn any advertising channel...
I'm calling sd_ble_uuid_decode with the following parameters on a PCA10040 board:
sd_ble_uuid_decode(16, 0x2000F7CC, 0x2000F7DC)
ram base = 0x20003150
vs_uuid_count...
I want to use in my project tft 1.8 display with st7735 controller. I used the standard GFX example from SDK 14.1 and everything is working fine, but the picture is incorrectly...
I have a QFN48 nRF52832, and it's getting hot. I'm looking at it with a thermal camera and there's a hot spot directly under the "N" of the "N52832" that's on the package...
The BLE_NUS_C_EVT_DISCONNECTED of the ble_nus_c_evt_handler() give a conn_handle = BLE_CONN_HANDLE_INVALID . So it's not possible to know which peripheral got disconnected...
Hi everyone !!
I'm a beginner in ble mesh. I'm working with nRF 52840. I'm not being able to figure out how to see log messages. I want to know where will following line...
