Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi,
When trying to update an app using Secure DFU, we get invalid object error. The error comes from dfu_decode_command.
Using nRF5 SDK 12.2.0 on custom nRF51822 board...
I have followed the CoAP example from IoT SDK,
I have a Raspberry PI set up as the router,
and two nRF52 boards, one is the client, the other is the server.
Following...
I have following questions:
Is there an example for implementing WeChat on a nRF52?
Is the nRF52 module supported for WeChat AirSync?
Where can i finde the requirements...
Hello!
I'm drawing a circuit with nrf52840 chip and I want to ask some questions:
Is it ok to use 2-side pcb (not 4)? what's of these better in part of radio communication...
Hi, I use nrf connect to programing demo board nrf51 dongle to get it work, failed.
error log as follows:
2017-03-02T09:30:20.014Z INFO Application data folder: C:\Users...
Hi,
Does the PPI module automatically clear the event flags for the linked event? For example, if I have the following:
NRF_PPI->CH[0].EEP = (uint32_t)&(NRF_GPIOTE->EVENTS_IN...
hi
I'm porting Arduino code which has calls to ShiftIn() to read a byte from a GPIO Pin and bitWrite() to write a bit into a byte variable at a particular position.
Below...
dear friends,
now i need to let a master 52832 device communicate with multiple slave 52832s.how can i make it? Our scenario is that a teacher takes a phone in a classroom...
I used SDK12.2.0 and S130 develop with 51422;
I want to test for fds write and read, I followed the fds_sample from github; it can write success, but no FDS_EVT_WRITE return...
I have to exchange information with smart cellphone. My 10040 board create a pair of key by micro-ecc and transfer the public key to the cellphone. However, the cellphone...
i am using timer 1 of nrf24le1.for which i have calculated a value which is to be loaded in th1 and tl1 for 1ms .calculations are as,
clock =16mhz;fosc=16mhz/12=1.333mhz;t...
Hey everybody, I'm having 'intermittent' issues with device addresses on the nRF24L01+. I've read the documentation on what you're not supposed to do as far as device addressing...
dear friends,
There is a pic that i catched using sniffer. SlaveLatency,a gap parameter,is set to 2.As you can see, when the slave do not give an ack,the mater will resend...
Hi
I am measuring the current.
I use SDK 12.2.0 , NRF52 and S132.
I noticed that current was flowing even while device waits events.
Device waits by sd_app_evt_wait...
