We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I'm taking a look at the timeslot API example here , which was linked to in the answer to this question .
Very interesting! As I gather from the documentation for S110...
Hi,
I would like to have accurate (1-5ms), synchronized timestamps for logging events from a set of nRF5x boards, spaced tens of meters apart. Each nRF5x board is connected...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I am struggling to find a starting point to be able to program the beacons. I'm completely new to this but want to be able to change the tx power so that they are only visible...
In my application, a static passkey is given to the user(I have implemented static pass key in my application and it is working).
Suppose the Nordic device is advertising...
In "ble_app_hrs_freertos" project, I try to change NRF_SDH_BLE_GAP_EVENT_LENGTH to 320 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 247.
And when I try to connect to the nrf52832...
Hi ,
I evaluate the I2c communication of your chip nrf52832.
I have few problem.
Write fonction
Is use your Tx fonction,
uint8_t reg[2] = {CCS811_REG_MODE...
Hello,
I used translation software.
I enter system on mode from the power_manage of the function.
But I do not understand system on mode.
In the system on mode is...
Hi,
After using comand line --rbp, recover fail,the nrfjprog error log as below:
--------------------------------------------------------------------------------
nrfjprog...
Recently I have been learning ble_app_uart routine, here is a question
When receiving the message sent by the client, nus_data_handler this function will be softdevice...
Hello,
I succeeded to port s110 & sdk9 to s140 & sdk14 which was a problem before.
What we need to do now is to compare the performance of BLE devices with s110 & sdk9...
Hi, I am a beginner programmer and I have the next problem.
I am working with nRF52832 SDK 12.2 trying to send AT commands to an ESP8266. I send the AT commands byte by...
Hi all
According to errata 146 of the nRF52832 Rev 1 errata sheet V1.5, the LFRC oscillator has a frequency tolerance of 500ppm instead of 250ppm.
What are the consequences...
