We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
I discovered unusual behaviour in a SPI read transfer.
My transfer consists of writing one byte (peripheral register address) and receiving one byte (contents of...
SoftDevice Version s132 SDK Version
12.2 Kit NRF52832 PC10040 DK
I am trying to run the ble_app_beacon example after importing the project into Segger Embedded Studio...
Hi,
My application always stops at the end of ble_stack_init() exactly at:
return sd_nvic_EnableIRQ(SWI2_IRQn);
of the function softdevice_handler_init.
My board...
I am working on a project using the nRFDK51 as BLE scanner with s130 and BLE peripheral an nrf51822 custom PCB design. The BLE peripheral is the device we are developing for...
How many nRF52840 chips can be used simultaneously? Can all data and advertisement channels be used at maximum capacity (2Mbps/each) to result in an overall throughput of...
Hi,
I am running an nrf52 (board PTR5628, no external 32kHz crystal), having some leds blinking at startup just prior to start advertising. 75% of the time when I power it...
Hello all,
I have created a BLE application on nRF52 PCA10040 devboard with S132 SD, in which I would like to use a PWM with the PWM_Driver .
My pwm source code as below...
Hello,
I am new to nordic nrf51822 and want to program nrf51822- www.raytac.com/.../MDBT40 spec-Version A5.pdf using jlink ( world.taobao.com/.../537881589911.htm .
I...
Dear friends,
As it said in title,when using 52832,s132 softdevice,what is the max number of packets that can be sent in one connect interval ? In which document i can get...
I have run into a challenge with the app_twi API, and I'd like to run it by you for your advice. To be clear, I am not blocked. But I am not pleased with the source code maintainability...
Hello,
I'm trying to implement DFU support to our application on nRF52832. I got it working fine with SDK11 SD2.0, but now SDK12.2 SD3.0 is causing "gray hairs". I used...
i have a nrf51822 mcu device, when it ok, i use Ultrasonic bonding technology to Assembled box,and today,many device crashed,is it related to ultrasonic?
Hi,
this is for anyone having problem with the eddystone EID after reboot. There seems to be a problem that the EID slot will write the encrypted IK to flash instead of the...
