I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am design a very compact board for my project and running out of space. For this I am planning to replace two DCDC inductors with a single one. Is it possible to do this...
I am communicating with the nrf8001 via SPI, from an HCS08 MCU. First thing I receive:
0x01 0x04 0x81 0x02 0x00 0x02
This makes sense, it tells me it is in setup state...
In my design I am planning to power up some sensors from nRF52832 GPIOs. Is it possible to maintain the GPIO state high during the low power mode of MCU?
Please guide here...
Hello,
I have been testing the BLE multilink examples for the s120 softdevice. More specifically, I have tested the ble_app_hrs_c example in the experimental s120 folder...
Is it possible to configure the parameters of the advertising library (eg. SDK v12.3.0 using SD130 v2.0.1) so that my peripheral device (eg. nRF51) changes after a limited...
I've configured peripheral for broadcast, but why can't IPHONE search it? I don't need APP development. I just want the phone to show it. Is there any special requirement...
Hi,
I was considering the following scenario and didn't find an answer. Could you please help?
Assumption:
There in a BLE peripheral (e.g. nRF52) and central ...
Im using sdk 14.0 and s132 When i add flashwrite codes to my project which has bluetooth communication ,it does not work I wanna send data to flash and i wanna read/write...
I do not want to use SoftDevice, I want to write new application from application to Code Area(0x00 - 0x80000).
Can I use fds without using SoftDevice?
Also, Is there...
Hello,
I am using SDK 12.2.0 with s130_nrf51_2.0.1 softdevice and running ble_app_hrs example.
My FLASH and RAM settings are:
FLASH (rx) : ORIGIN = 0x1b000, LENGTH...
Hello,
I am using sdk12.2.2 and pca10040. I want that my beacon advertises continuously for 10 sec and then it stops advertising for 5 secs. Do I need to use rtc for this...
As i am migrating to 52 and tuning the ble app, i realized by reading many posts here that:
external HF xtal is not recommended
external LF xtal can be replaced by...
Hi Nordic,
I am trying to implement DFU-OTA in beacon. For that I am trying to make beacon connectable. My requirement is to work the beacon in non-connectable mode during...
Im try to read the RPD register, but always get the same value RPD=0
uint8_t channel=0;
int index;
hal_nrf_set_operation_mode(HAL_NRF_PRX);
hal_nrf_set_power_mode(HAL_NRF_PWR_UP...
Hi ,
I need the BLE peripheral to have 'name1' at the start up and change it to 'name2' when a button is pressed. I want to do this without disabling and enabling the softdevice...
