I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I was able to add the Device Information service as well as a proprietary service using a 128 bit UUID. I modeled after the ble_peripheral uart example. However when I try...
Nrf52/Kiel/SDK11
My application was at the point where I needed to add DFU. Following the examples and SDK doc, I added the files and code needed. It would NOT advertise...
We recently moved from SDK11 to SDK13. We run out of memory when adding custom services & chars to the S132 v4.0 softdevice. Increasing the app start address in the linker...
For the record I have been struggling with migrating a project from S110 @ nrf51422 to S140 @ nrf52840.
Quite by accident, I found this "nrf51_to_nrf52840.h", what does...
Hi , Everyone!
Now i have the board nrf52832 and i'm conducting my DFU.
My DFU is to update softdevice and application.
Here is detail about my problem:
softdevice...
Hi
From s140_nrf52840_5.0.0-3.alpha_migration-document, it is mentioned that the L2CAP API has been completely removed. Are there plans to re-expose the API? We have exposed...
I'd like to clock the nRF52840 at the same frequency as my converters. Is there any problem with using a somewhat different frequency than the 64 MHz (or 32mhZ) crystal? If...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...
I'm looking for an answer as to how to know the source files that I need to mention in the Makefile if I'm writing my program from scratch. Are there some bare essentials...
Hello,
I am writing here because I am trying to change some concrete values from a .hex file in order to vary some BLE and other values. I need this because I need to generate...
Hello,
I downloaded the nRF Blinky app (for Android) here :
github.com/.../Android-nRF-Blinky
I'm looking to modfy the code to have an auto connection. For this, I...
As far as I can tell, the application is set to invalid (settings.bank_0 = BANK_INVALID_APP) after the application has been successfully deleted ( devzone.nordicsemi.com/...
im trying to use nrf_drv_timer_t with timer0 but I get identifier "TIMER0_INSTANCE_INDEX" is undefined error. TIMER0_INSTANCE_INDEX is defined in nrf_drv_config but this file...
