I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hi.
Faced with a strange situation.
Example. All look good when I read code area:
void ex1 (void)
{
uint32_t *addr_out;
uint32_t i,word;
addr_out=(uint32_t...
We've developed a custom board based on the nRF51822-QFAA and an MPU-6050 IMU. It runs on a li-pol battery and uses S110.
I've encountered a strange problem when power...
Hi,
I am working on measuring the voltage on a lithium battery (norminal 3.7V) with a voltage divider on nRF52832. The voltage divider combines a 510K and 360K resistor...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
We have a custom board using the ISP130301 BLE module (containing a nRF51822, 16MHz xtal, 32kHz xtal). Our apps work fine (gcc, SDK6, S110v7) except for high system on idle...
i don't see where the command queue index, m_op_queue.rp, is initialized.
when queue_process is called, the following line blows up:
fds_op_t * const p_op = &m_op_queue...
Is there a way to reject requests when the whitelist is empty? I support clearing out the whitelist, but after clearing out the whitelist I would still like to reject connection...
Hi,
I'm using the nRF5_SDK_12.0.0_12f24da and S132 on nRF52832. I do the multilink based on the ble_app_multilink_central example. When it has connected to the peripheral...
Hi,
I want to use spi list feature without ppi. Is that possible?
Because I have to use the same spi module for OLED, SPI flash and accelerometer with FIFO, spi ppi...
Hi There, PCA10004_Schematic_And_PCB.pdf
We are working on Nrf51822 chipset and have observed in our case that once we download the code we are able to discover the device...
What I am trying to achieve is single-file executable for nrfutil tool, for performing DFU.
I downloaded sources and built it using pyinstaller. I can succesfully create...
Let's say I have my android phone connected to the nrf52840 device via bluetooth,
and let's say I change preferred phy from 2 Mbps to 125 kbps, would the connection with...
in my case sdk10.0.0 and I can not update sdk.
please help me to write sd card. if file system not possible ,please explain how to write raw data like sensor value 1000 time...
nrf52832 sdk12.2.0 s132.3.1
Hello.
Can't write properties after flash experimental_ble_app_buttonless_dfu example into chip.
I can only enter into bootloader using button...
