I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Makefile (/attachment/ca6852bdad7b5e54aaa4ce4388c4c410)Please find my code attached!!!
I have changed the makefile and the SDK config file accordingly! but the error remains...
Why can not read twi data ? at nrf52832 chip....
but Read well in Arduino....
twi interfacing with RTC DS1307....
please give me some hint.....
nrf_drv_config...
i would like to print register values of an external sensor on my screen using UART! I'm reading and writing into those registers using SPI! Printing a normal message using...
Im working on 14.0 and s132 and work inside ble_uart code...i was add rtc inside that code sucsessfully but now.. when device goes to sleep so rtc interrupt handler function...
I have just changed line 74 of nrf_drv_uart.h file as
#define UART1_ENABLED 1
instead of
#define UART1_ENABLED 0
and the example gives an error. Please find...
So i am utilizing SPI and i got it to work, however for some absurd reason after removing the segger_print statement below from before the while loop the spi would stop functioning...
Hi,
I'm working on nrf51822 and mpu9250 imu sensor.i'm facing a problem,my buttons function i.e buttons leds int and mpu9250 are not working together either one is working...
Hello,
I have a problem.
For example, I am using UART, and I had trouble printing everything when I used "app_uart_put ()" continuously.
My source is simple.
int...
Currently i am running a BLE project on the SDK 14.0.0_3bcc1f7.
And i would like to deploy the Nordic Mesh into it.
The Mesh that i am using is from the Tutorial, which...
MS76SF2_SCH_V12.pdf Hi,
I am using SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, NULL); for ble_Stack_init() because the off the shelf board (not from Nordic...
my company already have firmware with nRF51 and SDK11
recently, we made new Firmware
watchdog timer feature
so we modified application and bootloader
...
Howdy!
Before I break out the Segger JTAG, I thought I would try nRF Connect DFU upload. As I had a failure on OTA update there was not issue about being in DFU mode. However...
In this file: components/libraries/cli/uart/nrf_cli_uart.c
The function as defined:
static void uart_error_handle(app_uart_evt_t * p_event)
{
if (p_event->evt_type...
I have been trying to find a document referenced here 1 .
The reference reads as follows:
For more information on both modes, see sd_app_evt_wait and the nRF5 Series...
