Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Dear Nordic Support,
I am doing some test on the Thingy:91 v1.0.0 in Vietnam. I am running 2 examples: Asset Tracker with NB-IoT + GPS and GPS .
When I use the stanalone...
Hi,
How i can make the low power node to wake up until get acknowledgement . Please tell me how many ways we can try...In my project i used initiate_friendship() function...
It appears to me that the zb_zdo_ep_resp_t struct is missing a variable value attribute since the actual list of end points is missing. Should it not be similar to zb_zdo_match_desc_param_t...
Hallo All :-)
As an enthousiast hobbyist I've developed a custom board around an nRF52832-CIAA. When I started testing with a BLE secure bootloader from the SDK16 examples...
Hi,
I am currently working on " asset_tracke r" application. Actually, I need to read 128-bit UUID values of the BLE ibeacons present nearby the board (PCA10090) to be captured...
Hi, everyone!
We try to use THINGY:52 board for debug our MEMS lib from external sensor. But before use external sensor (i2c bus) i can't burn standard firmware that compiled...
Hi all,
I'm working with the reception of 802.15.4 packets on nRF52840 for which I have configure the radio as follows:
In the application loop we have:
...
Hi,
I am using nRF52 SDK v16 and I am wondering where one can find relevant information regarding peripheral event handlers.
Here are a few puzzles I have for now:
...
the central(phone) connected my board,when i call sd_ble_gap_disconnect ,sometimes,not every,return err_code =0x00000008,and not firing BLE_GAP_EVT_DISCONNECTED,also not advertising...
Hello All:
I am working on the time service of NRF52. As I know, there are two standard profiles refer to the time service, one is CTS(Current Time Service) and the other...
Hi All,
I am doing a BLE Mesh development project with nRF52840. SDK version: nRF5 SDK v15.3.0 & nRF5 SDK for Mesh v3.2.0
Case 1:
- IDE: Keil
- Example tested: nRF5...
Hi,
Im working on a configuration where role switching is neccessary.
The following is expected:
- all nodes will be advertising when "idle"
- nodes only need to...
Hi,
When the ble_stack_init(); is called the eeprom flash read/write/erash gets hanged.
But when commented ble_stack_init(); the eeprom flash read/write/erash works...
