Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I got stuck drowning in all of the sdk's and softdevices..
i've recently bought EYSGJNZWY BLE chip with nRF51822 built in.
The chip comes with s120 built in, I can see...
I have two nrf52538 dev kit configured to work as peripheral(s) with simple static pass pairing program and Android phone as client. 1) peripheral_1 address = 0xCECECECECE...
I have three mesh nodes in a mesh network, a provisioner, a vendor server model, and a vendor client model.
I know that a provisioner can set client model publish address...
Hi,
we are using active voltage divider as battery readout circuit. It is controlled by MCU NRF52832 pin P0.09. Voltage from divider is read by integrated SAADC on pin P0...
Hello,
I'm working with the nRF52840 PDK and the SDK for Thread V0.11.0. The RTT Viewer shows that the program uses the Thread version OPENTHREAD/ga89eb88-dirty.
I try...
Hi,
I was trying to follow the guide to enable unit test of mesh SDK, but cannot get it through yet.
When I run the command
cmake -G Ninja -DBUILD_HOST=ON -DCMOCK_ROOT...
Hi,
I am using the nRF52 PCA10040 board. The memory settings are IROM1 - { start 0x1B000, Size 0x65000 }, IRAM1 - { Start 0x20004000, Size 0xC000 }. The board was working...
Hi，
my ble device mcu is 51822 with sdk11，when my ios app on frontend，it can search the ble advertising immediately，but when my app runs on background，it can't search the...
Hi,
I did some benchmark on internal flash access and found it takes more than 2 seconds for the device to write 16kB data. I timed by "nrf_fstorage_is_busy". Is this normal...
Hello,
I am using the sd_ble_getts_value_set() function two times in a row on two different characteristics. Both characteristics are part of the same service.
At the...
Hello,
I am really new to using the Nordic nRF51822 and I'm having problems making SPI work with the S110 SoftDevice. I was able to combine the sample codes spi_master_example...
I am using a nRF52840 PDK and trying to config 8 buttons.
(1) GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS to 8 (sdk_config.h)
(2) Add buttons define (pca10056.h)
Button...
