Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I connect one central and two peripherals
Both peripherals set the connection interval to 100
Observing PA / LNA shows that one is communicating in 100ms
But the other...
Hello.
I have question about output OOB and public key.
I create my Android app for Thingy Bluetooth mesh purposes. I would like to start output OOB process (then Thingy...
Hi,
I am using the nrf_log_backend_flash in SDK15.3 with IAR 8.32 on Window10. From what I see in the release notes, no improvements were made for 16.0.
In my application...
Hi,
Good day!
Statement of porblem: We are developing appliction using nrf52832. In our application we have Capacitive touch button and capacitive wheel sensor for user...
Hi,
I am using bootloader and application based on SDK15.3.0 and SD s140_nrf52_6.1.1_softdevice.hex.
I am also using our own BLE transport layer in application to receive...
Hello, I can see in the datasheet of the NRF52840-CKAA-R that the recommanded inductor value for DCCH is 10uH +-10% (configuration no. 4). Unfortunately, we experience some...
Or may be another procedure to make a list of surrounding beacons nearby using nrf52832. We are beginners, sorry.
What do you recommend to start with?
Sdk16, 7.0.1 Softdevice...
Hi,
I have configured pin 10 (STATUS_BUTTON) on my own design board using a nRF52832 chop as follows:
I am intending to use the internal pull-up resistor to pull the...
Hi,
I'm trying to emulate a server device with pc-ble-driver-py, I recently moved from version 0.11.4 using Python 2.7.12 to version 0.14.0 using Python 3.7.4. I'm trying...
Hi,
I am using segger studio and NRF52810 for my development. I started with the NRF52 dev kit and complied with the sample app given in PCA10040e folder.
Now I want to...
Hi All,
I'm trying to figure out the best way to implement the security between two industrial IoT devices. We don't have a good out-of-band channel for more "traditional...
Hi,
I'm using Thingy:91 and I have built and flash the asset tracker software. I have connected the external GPS antenna (MIKE3A or similar), see picture.
How do I check...
I am using nrf52832 chip along with softdevice as a peripheral. There is a requirement wherein we want to encode the advertisement data.
Came across ble_advdata_encode(...
I'm reviewing the ringbuf library for use with FreeRTOS across two threads and I can't see how the atomic operations implemented in the library make it thread safe. The atomic...
My debug uart stopped working after creating overlay files to make port changing easier. Is this a known issue? They're still the same pins and baud rates.
