Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi
I don't have the board space for a loop antenna, so I'd like to use a dipole. What sort of RF output / matching stage do I need for this on the nRF905?
Thanks!
Hello
I wrote the program by referring the some examples after compiling the program GPIO pin becomes high immediately (3.3V ) bu my aim is to make the GPIO pin as output...
I have two nrf24l01+ modules communicating on a single channel. The "remote" does 99% of the data transmission while the "base" receives and uploads to a host. Occasionally...
How to use stlink or CMSIS - DAP downloading S110 protocol stack? Jlink can use nrfgostuide down s110 protocol stack, i want to know how to use stlink or CMSIS - DAP download...
Hello,
Is there any information on current consumption for the nRF51822 when running the micro-esb examples? I'm curious as to how much current is being used in a situation...
I'm testing a custom board I did. The board has this 16Mh crystal
geyer-electronic.de/.../GEYER-KX-7_01.pdf
The CL of the crystal is 12 pF. I'm using a pair of capacitors...
Hi,
I am trying to get the ble uart example from the sdk 0.9.2 working on my nrf52 DK board.
But the nRF UART v2.0 application on my android phone, quits instantly after...
Hello,
I'm looking to send a 32 bits word to the example "LebButtonDemo", using an iPhone application created with Evothingd Studio (it uses Javascript).
I'm able to...
Hello
at the moment I have a running S120 BLE firmware update on my nRF51822 hardware.
This works fine on my desk.
But we have the additional requirement to update the...
Hi
I have an custom board which uses an nrf51422 SOC. I am facing issues with my radio.I use an softdevice s110 with an application on it.
The code just works fine with...
Hi Noedic,
I triggered the DFU function through APP, the device restarted and the base service UUID changed from 0x0001(nus function) to 0x1530(dfu function), but it is...
Hello,
I am working on S120 SD v2.1.0 for central and S110 v8.0 SD for peripheral and SDK9.0 and I am able to configure 1 single uuid on central and connect to multiple peripherals...
Hi.
I would like to konw some ditails aboute nRF9E5 device:
What is the rang between 2 devices using 433 mhz.
do you have any samples codes ? i need to trasmitt...
Hello,
After i disable SD i try to count ticks on TIMER1 from RTC1 via PPI.
Timer1 is configured property but TASK_COUNT don't increment cc.
I see that event TICK on...
