Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi
nRF52833, SDK16
When using a UARTE interrupt I get a fault which I cannot locate, I have the following code:
When my 4 bytes are recieved, i get a fault and the...
Hello,
I'm chasing a bug and narrowed it down to a minimal failing case. Even it's only very few lines, I'm still failing to grasp what's actually happening.
Taking the...
Hey guys,
I'm working with SES, nRF52832 and SDK14.2.0.
I have a timing problem and would like to describe the problem from the beginning.
I have a 1-wire temperature...
Hi.
I'm having Segfault issues with our company's custom boards based on nRF52840 chips.
I do several re-flashing with J-Link EDU Mini Programmer on a daily basis with...
Hello, I am reporting here an issue that I detected by using NRF connect on iOS (cf https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/56 ) The issue is that the...
Hi,
I use SES IDE, nRF5_SDK_16.0.0, nRF52840 DKs. I am using ble_app_uart_c as a template for my application that needs to connect to multiple peripherals whose device names...
HI All,
Using Nordic devices and with my mobile I am able to do bounding and pairing.
But, after that, I have deleated the bounding information from Mobile.
Now, If...
Hi all,
I am trying add Long range to NRF52811 (app_uart_nus and app_uart_nus_c) in SDK 15.3
I checked this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hello,
About RTC module, Systick and SoftDevice.
Does SoftDevice make use of RTC module events ?
Does SD also make use of ARM SYSTICK ?
Note : we do not use FreeRTOS...
I have implement an in-app DFU procedure based on Nordic's dfu ble service. The images are saved into external norflash and then control is passed to a bootloader which validates...
Hi
This is my code for antenna switching. I've got 8 antennas I want to switch between.
NRF_RADIO->PSEL.DFEGPIO[0] = 0x00000011; //(P0.17) NRF_RADIO->PSEL.DFEGPIO[1] ...
I am using nRF52832 on my device. I have used SDK13 and softdevice 4.0.5.
On any iOS devices I can scan and connect in the nRFConnect app.
On an older Samsung Galaxy S5...
Hello,
we need some advice to choose the right TX power. We still wonder if TX power +4dBm is the best choice or better use the default 0dBm.
Here is some background...
Hi,
We are working NRF52832, SDK15.3. It works properly in debug mode but when I build in Release mode it is not working.
From my understanding debug mode will have symbols...
i use the demo ble_app_uart ，and i want to close the uart when ble is "Disconnected"。
but it when it do app_uart_close(),the nrf52810 is RST。 i use the same code in nrf51822...
