I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
hi,
1.I find some same issues on website, most of them can send more than 1 packet per connection interval up to 6 packets, but I'm not sure what version of sofedevice...
Hi!
We are using S130 softdevice in peripheral role and achieve the specified maximum throughput of 63.4kbps ( S130 spec ) when communicating with a PC and connection interval...
Dear sir,
Reader has a NRF24L01P-R7 with stm32f4xx controller.We are using TAG chip NRF24LU1P-F32Q32-T.
Please share the independent stack information(source code) so...
I am trying to setup the examples for the dev board PCA10040. I copy them from the Pack Installer and when I open the project I keep getting "Install missing Software Packs...
Hello
I made a custom service with characteristic. It send the number 1234 over ble. When i open the Master Control Panel and look at the custom characteristic. I read...
We have a home made BLE device based on nrfR1822. This one has two embedded sensors sampling data at a frequency of 25Hz.
In regular mode, the device sends every second...
I was going through Gazell link layer as well as Enhanced shortburst i found in both of them we can use payload max upto 32 bytes. Both supports 8 nodes with an host using...
I just received the nRF52 demo board PCA10036 V 1.0.0, and I also downloaded the latest SDK nRF52_SDK_0.9.2_dbc28c9
I programmed the softdevice hex and then programmed...
Hi BLE Developers,
I'm developing a BLE peripheral device using S110 softdevice which doesn't have any input or output capabilities and will communicate with smartphone...
Hi,
I am using the iOS nRF Toolbox and integrate it to my Swift project.
After that, I got this error message.
Undefined symbols for architecture x86_64:
"_crc32"...
my dk board : nrf51422 and nrf 52382,
the central role : nrf51422, and the peripheral role is 52382.
my sdk version : 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I've been trying to wrap my head around the app_twi library by looking at the examples, and I'm slowly getting there.
However, for my application I need to send multiple...
There is a fair amount of documentation suggesting that a Raspberry Pi or consumer router running OpenWrt can be set up as an edge router for Bluetooth.
The builds involve...
