I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
In the case that I used custom board, I used bootloader_secure to OTA; but after OTA, the program doesn't jump to the application, even app nrf connect notify Sent Successfully...
Dear Community;
I am running some current measurements on the NRF9160 DK. I am following the manual instructions:
1.-I am powering the NRF through external power supply...
Aim: transfer large data coming from UART to nRF52832 over BLE 5.0 as fast as possible. Want to use 921600 baud rate in the case given below.
Scenario:
SDK: 15.2.0 ...
I have created an out of tree board folder following the same pattern as the Nordic PCA10090 and that is working as expected. What I would like to do now is have 2 versions...
nrf52832 sdk16.0
my program initialize as below：
advertising_init(m_advertising_data_init_array,10);
adv_scan_start(erase_bonds);
scan and advertising is ok，but when...
Cannot connect to ATECC508A through TWI with NRF52832. Tested with nRF5_SDK_12 twi_master and deprecated twi_sw_master. It was working fine only with NRF51822 nRF5_SDK_12...
Hi,
we would like to use a production ready open source RTOS with our nrf52840 development under Linux (with eclipse or visual studio code).
We have tried with mbed...
I am using nrfmesh android app. I have configured a mesh network. exported network. then reinstalled app and connect to network. then tried to read state of device, then get...
A mesh node contains multiple lights.
Assume a light contains 5 Elements (Main, Temperature, Hue, Saturation, Light LC). Each light has 30 model servers implemented.
When...
Hi,
I am trying to test ble_app_blinky app. I am using VS Code for the development IDE and while compiling the application using MAKE I am running into Cannot file Source...
We are seeing about 500 uA in sleep mode and we expect to see under 2 uA. We are using an nRF52810 on a BMD-330 module on SDK 16.0.0.
Here's the relevant code...
nrf_pwr_mgmt_run...
Hello all!
How can I get the current count of a timer without stopping it?
Right now I'm doing like this:
_timer_base->TASKS_CAPTURE[channel] = 1; uint32_t counter...
Hi,
I am no programmer, but I wanted to try the Wake-on-NFC example on the 52840 dongle (I soldered an NFC flex on pins P0.09 and P0.10). I have downloaded SES and nRF SDK...
I want to connect heart rate sensor and bike power sensor together. I config channel 0 for heart rate sensor,and channel 1 for bike power sensor. Ant work well when both sensors...
I've just tried to compile and run the stock lpcomp example on two different computers, targetting an off-the-shelf 52840 dev board. It compiles, and starts fine, but doesn...
