Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hi All,
In nRFMesh app we can see the list of names of available Bluetooth devices. Is it possible to see the list of names of available Bluetooth devices using static provisioner...
According to the spec, this is how a bonded reconnect should work:
On first pass, the central client does discovery and enables descriptors to characteristics of interest...
Hi,
I've got an application based off the asset tracker firmware that needs a UART. From the many threads on the topic, I've found a way to shut down the UARTs to save power...
Hi,
I tried out the light client example in the Mesh SDK V4.0.0 and it works so far. Now
I added more data in the messages and it works, but only as long as the message...
Hello all,
I have a pretty simple question that I hope can be answered for me. I'm integrating an nrf52832 development kit (PCA10040) BLE sniffer into a test fixture to...
hi,
i able to write and read unsigned integer value from the flash, but when i try to write some string to it ,the device is not responding.
void Reading_the_data_from_flash...
Hello Sir,
I would like to ask about the handling of the interruption in the nRF52 SDK.
The versions for SDK and SoftDevice are 15.3.0 and S132 v6.1.1
In the processing...
Hi all,
I am using a nRF52840 with SDK v16.0 on SES. I am trying to understand the flow of code in the secure Booloader(/SDK_v16\examples\dfu\secure_bootloader\pca10056_s140_ble...
Hi ,
I am trying to interface sg90 toy servo with NRF52840 , I am using nrf library but dont know how to drive it from 0 degree to 90 degree to 180 degree . May I know the...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
