I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi all,
I have a question regarding the difference between the nRF51822XX AC and nRF51822XX AA during the configuration of IROM and IRAM in Keil software.
I know that...
To the kind attention of Nordic support team,
We are going to use nRF52833 in our products, and we would like to embed in our PC side software (driver) a custom version...
Hi there,
I'm developing a custom board that integrates a NRF52840 based BLE module from Raytac. I was wondering if it is possible to upload the Adafruit nrf52 bootloader...
Hi,
I am implementing LESC on nRF52810 using an example.
Unfortunately, I didn't find any examples.
So, I am programming the PCA10040e with reference to the PCA10040...
Hi,
I am new to NORDIC dev and I find its ppi is really useful but also difficult to understand.
Now my device may be connected the truck engine to count the engine speed...
Hello Team.
I have NRF52840 Development Kit. here is description, what I want to do and How I am doing.
I will send command on terminal and kit will start scanning for...
Hi,
I developed a product using nRF52810 and am now preparing for mass production.
However, since I have no experience in mass production of Bluetooth, I would like...
Hello my current setup use :
nRF52 dev kit
Segger Embedded Studio V4.4
SDK160098a08e2
s132
nRF connect on a iPod touch
I can compile and once connected appreciate...
I am looking for example code on the EV-BT840(832)-V4 dev kit. I can program it with the hex file and it works, but when I program with the nR52 SDK example codes thru Segger...
I am trying Bluetooth mesh light-switch application on microbit, and I have flashed with same light code on multiple microbit devices, Though all the devices are getting detected...
Hi! I am currently writing a DMA driver for UARTE which with the goal of being able to handle large data transmissions with little software intervention as well as handling...
Hi Team,
We are using nRF9160 DK, We tested the asset tracking application with the DK. It is connected to nRF cloud and the data is sent from the DK to cloud. This is...
Hello, I am working on a script on Jlink to be able to flash from my raspberry. I used to have a batch script using nrfjprog and I didn't know how to translate these commands...
Hello!
I have both SD Card and accelerometer in same SPI bus. Both of them working like charm if another is not present. I'am using app_sdcard from 52 sdk.
Can i use spi...
Most of the SDK Peripheral examples support only a single connection.
Is there a guide somewhere which explains and illustrates what, exactly, needs to be changed to update...
