I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi,
I am currently working on a project with nRF52 preview DK.
In my system, an ECG chip is used to measure the heart rate and the data will be transferred back to nRF52...
Hi,
I have a number of products with nRF905 successfully deployed. Now, I am in a little struggle with a new one. The problem is the signal strength. The other products...
I'm trying to add a feature where my peripheral will temporarily trigger a Faster Connection Parameter for a period of time determined by an app_timer. However it seems that...
Hello Nordic Devzone.:
When studying the 8.0 BLE Central multilink example (s120 softdevice), I looked into the component relevant to button pressing interrupts, app_button...
How do I use the NRF51 or 52 to create a GATT server with read only service without requiring bonding? Basically I want to be able to provide more data than advertising allows...
I can not connect to one of my beacons, i need to reset its config, but HW way.
Can i reset it somehow?
It is nRF 51822 based, sensoro 4AA. I asked sensoro 3 days ago...
Hi Nordic guys,
we are using uart for communication with another MCU and flow control is used.
Beside the uart communication itself we have out of band signals (on gpio...
Dear Nordic.
I have used to nrf51822 custom device. I confused it because of Uart RX data.
The master device sends blow raw data to client device(nrf51822 custom device...
I'm trying to compile a program on mbed for a BLE Nano, which uses the nRF51822. I've included the nRF51822 library by Team Nordic that's listed on mbed's library wizard and...
Hello
i am trying to upgrade from sdk 9 to sdk 10 .zip version but after installing when i open some examples it asking me to install arm cmsis 4.5. pack and device family...
Hi can anyone guide me in configuring the peripherals of nrf51822 before putting the chip into sleep? For example, timer, i/o pins, etc... which is not needed to reduce the...
Hello, please help me to find nRF52 datasheet, in which are recommended WLCSP footprint, and of course schematic drawing of this module. In your Dev Zone I found only QFN...
