Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi
I tried SDK6.0.0 porject at below link.
C:\Keil\ARM\Device\Nordic\nrf51422\Board\nrf6310\s210\ant_bicycle_pwr
According to SDK documentation, we didn't need to modify...
Hello!
I need more battery life and higher resolution in my applications. That's why i need to level down the signal power, if it is possible. Thanks in advance.
Hi,
I'm using nRF51822 Bluetooth Smart Beacon Kit. Is it possible to to switch between
beacon mode and configuration mode without the need to press SW2 button e.g.: by...
How do I keep advertising when I have a connection come in? I'm a BLE peripheral.
I'm running SD 7, is there a particular flag or sequence I need to do now that I've upgraded...
Hey!
I'm testing out the new SoftDevice and am trying to update firmware OTA but thus far have not been able to do so. I've tried from the Master Control Panel android...
I'm using NRF51822 as SPI slave and STM32 as SPI master. Everything works fine except the first SPI transaction after resetting both boards.
On the first transaction I...
Hi guys,
I'm curious whether or not i can try the mbed platform on the EK board. The circuit of the mbed kit and the EK look pretty similar. All the LEDs and buttons are...
I'm using the NRF51822 - I've just started a project. I can build and load it into my target board. I enter debug mode, and I'm able to do step through the code, add breakpoints...
What are the iROM and iRAM settings for the v0.5 S130 softdevice for the nRF51822?
The S130 softdevice spec sheet provides some clues, but no specific settings.
I've...
To do development what software did you have to install, and what hardware did you need to get the MBH7BLZ02-EB-KIT working? What hardware did you connect together?
There...
Hi
I'm learning to use the sd_flash_write function to write words into flash memory. I've the SD enabled, but not advertising, so I'm able to debug. Scheduler is also initialized...
Hello, I am trying to make a portable temperature sensor using nRF51822. I made a sensor that basically amplifies voltage level when the temperature increases, and I want...
Recently, I try to programme nRF24L01P DK communicating with nRF2401e1 DK in shockBurst mode, transmitting and receiving,unfortunately，which does not success normally.
first...
