Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I created firmware to nRF51822 Development Kit but I have a problem with connection. PCA10004 board is programmed to advertising packets whole the time and measure battery...
Hi ,
We are using nordic nrf51822 custom board.
In our we are not using any external oscillator.
so here is my configuration for advertisement in ble_proximity
...
Hello,
I have posted a question regarding the HID template code for the nrf8001. I would like to say that the progress from your help has helped immensely.
Currently...
I am having an interesting issue trying to send packets. Only a very small number are being received (~1 per second even when transmitting one after another), and they are...
I want to use a UICR for device serial number. Correct me if I am wrong but it is my understanding that a UICR cannot be changed programmatically like onboard flash can. So...
I'm using the UART to talk to a GSM modem. It has hardware flow control and supports a baud rate of 115200. I'm using app_uart_fifo.c, not app_uart.c. I'm using the SoftDevice...
Hi,
Does Nordic Semiconductor provide any resources (codes, macros, documents) for work with IAR or Keil's simulator to fully simulate nRF51822's peripherals?
Thanks...
Hi,
I do:
err_code = ble_bondmngr_bonded_centrals_delete();
APP_ERROR_CHECK(err_code);
till now all is ok.
But when I do:
err_code = ble_bondmngr_whitelist_get...
Hi,
I need to delete all centrals using ble_bondmngr_bonded_centrals_delete ble_bondmngr.c function. It is working but it is not cleaning the whitelist.
So, when I do...
In the example of hid_mouse, ble device will bond master when disconnect event happen.
I try to add this two codes to Implement my idea.
err_code = ble_bondmngr_bonded_masters_store...
I write this code to set my ble device power down,but it causes reboot without any error report.
GPIO_WAKEUP_BUTTON_CONFIG(LEFT_BUTTON_PIN_NO);
GPIO_WAKEUP_BUTTON_CONFIG...
I try to use 51822 to run ANCS sample(ble_app_ancs). It work well and I can get notification source and notification attributes. But I don't see any source code for get App...
Hi
I've a reproducable behavior i'm not able to explain. I'm using the softdevice S110 6.0 on a nRF51822.
The firmware implements some BLE profiles and uses TWI Master...
Is there a way to map external memory (SPI connected) to force the app to start execution from there ?
If not feasable , there is a way to transfer the execution from internal...
I have a 51422 board design and I just got Ant-FS working with our firmware so I can now download data from an external SPI flash to a desktop application.
I want to be...
