here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Is it normal that after cutting SB8 our chip is still working when connected to USB port? (in case of battery we need to connect pin 1 and 2 from P1). I spend long time looking...
I have a custom board that uses the nrf51822. I have been using the sample application ble_app_uart with only one minor change, I use the internal clock (NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION...
I'm wondering when my firmware changes over time what will happen with information stored with pstorage? For example if I my new firmware release adds an additional pstorage_register...
If I have persistent data that will be updated semi-frequently, will pstorage wear out the flash memory? What steps should I take to be sure my data storage will remain functional...
Hello,
I tested nRF51822 with ble_app_hids_keyboard example, i found it cannot pair with more than one devices.
Procedures:
Pair PCA10001 with iPhone#1, it can...
Hello.
I have a nrf51822 ek and trying to create my software using same technics as the bootloader example from sdk. But sdk's bootloader in my case doesn't work. I programm...
hello all:
I have compile successfully my project.but have link trouble about my project codes for the nRF51822 with the Keil MDK-ARM toolchain (v4.6).
For example, for...
When I try to read attribute with authorization and reply on request with status BLE_GATT_STATUS_ATTERR_INVALID_HANDLE, my device (nRF51822) goto app_error_handler method...
After importing every of your android project demos to eclipse I have following warnings:
This Handler class should be static or leaks might occur (com.nordicsemi.nrfUARTv2...
This must be stupid question of the day. I have my nRF51822 kit and my nrfGO kit and I can't find the product key. On the box for the nRF51822 there's one tiny sticker with...
I'm using Maple and custom nrf8001 board... I have the following problems...
I'm usign the library from this topic:
forums.leaflabs.com/topic.php
But as you can guest...
I've managed to get my 85122 dev board set up on parallels on a mac and get 'blinky' uploaded to it using Keil and nrfGO studio. I then changed blinky to do something else...
What is the exact meaning of this error code? Is the pipe busy? The nRF8001? The peer? Is an indication of something I did wrong, or just a indication that something needs...
