Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi I have built a custom NRF8001 board and I'm debugging a problem.
The main microcontroller works fine (atmega32u4) but the RDYN line never goes low to start the setup...
I am starting development on the nRF51422. I noticed that for the non-ANT sample code (blinky and UART), a gcc makefile and windows batch files are provided for compilation...
Hi,
Does the heart rate demo in SDK v4.4.0 work with SD v6.0.0? I'm using the QFAAC0 revision of the NRF51822. The demo works fine with SD v5.2.0. Is there anything special...
So far I haven't run across any code examples that will switch the BLE (S110) stack in and out. I'm looking to test enabling and disabling of the softdevice to see how that...
I'm reading AD-converter data usin nRF51822 SPI-Master. BLE-stack is active so I can't use
interrupts with SPI. I get data every 2 ms. Sometimes Events are delayed so long...
Hi,
We would like to implement a scenario that need two BLE devices,
One is Peripheral that able to broadcast and connectable,
another one is Central that able to scanning...
Hi,
I'm using nRF51 SDK v 5.1.0 with SoftDevice v6.0.0 on nRF51822.
I'm using the pstorage SDK module for flash operations.
I've found an issue with this module,...
Hi
In the product specification the S120 softdevice it is mentioned, that the S120 will support central and broadcaster role at the same time. This is exactly what we need...
I've cut the BLE proximity app example code back to doing nothing more than this:
int main(void)
{
uint32_t err_code;
leds_init();
for (;;)
{
power_manage...
It takes about 30s after I power my nrf51822 DK with ble_app_hids_mouse demo, how can I short it less than 10s ?
In the code there is a line
"#define NEXT_CONN_PARAMS_UPDATE_DELAY...
Would like to know whether you have a diagram for the RF pattern for nRF24L01. Like whether the node can receive other nRF signals 360 degrees around or should be at some...
Hi, I need to select the values for the crystal capacitors (C1 & C2) for a nRF51422 pcb.
From page 9 of "Crystal Oscillator Design Considerations" I see:
C1' = C1 +...
Hello,
I'm assessing various ways to authenticate/secure a connection with BLE on Nordic nrf51822. Our goal is to enable authenticated modification of a few values in a...
Hi
I see this in our own firmware and also in the sample HRS on the PCA10001
(If you try with the HRS app, then modify the app so that on BLE_GAP_EVT_DISCONNECTED instead...
I'm trying to get a simple, single shot timer working. The debugger never stops at a breakpoint set in my handler function, and an LED turned on in that function never lights...
