Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello! I'm trying to make what initially seemed like a straightfoward program - a bluetooth-to-hid adapter. Since Nordic's sample (BLE Central HIDS) uses the hogp and bt_scan...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
I am getting a bt_hci_core: HCI driver open failed (-11) with a custom board using nrfConnect for VS Code and 2.9.1 toolchain/sdk.
The code is really simple (I'm not...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I am working on project using thenRF9151 board and I require the GNSS functionality to work for the same. However, my board is not able to latch on to a satellite network...
We are using Thingy:91 X as an evaluation platform for our upcoming product. Our test application is made up of a nested-loop structure like
while(true){ lte_lc_connect...
Are there any specific points using the external flash of a Thingy:91X?
I tried to adapt the "nrf/samples/cellular/modem_trace_flash" by adding an overlay copied and modified...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
Hello Nordic Team,
I'm developing a ranging application on a u-blox NORA-B1 module (which contains an nRF5340) and have encountered a stability issue with the Nordic Distance...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
