hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
I upgraded to the 4.3 nRF51 last night and am suddenly having a whole slew of issues:
(1) When flashing the EK, the Segger now reports 257K of Flash (maybe it did...
Hi,
I'm looking to work with a Bluetooth LE master device. From what I read the nRF51822 should be able to function as a Master device (the dongle is configured to be a...
Hi all
I want to load the (UART_example) flash image compile with Keil by nRFgo studio,
but a program fail occur as below screenshot:
any idea?
Thanks.
I have test RTC example on both different hardware revision nRF51822 chip.
1)N51822 QFAAC0 1309AF
2)N51822 QFAAC0 1308AE
1309AF revision chip is function properly with...
I'm confused about how to assign a functional block's I/O (TWI in my case) to a particular pin on the device. Is there a worked and documented example? Is there a relevant...
I am trying to get wireless communication implemented on a robotics project I am working on. I'm using a PIC18F4550, PIC18F2550, and two Nordic nRF24L01's. I'm having trouble...
I'm attempting to have two separate evaluation boards talk to each other through the GHz Radio. I've read the docs, and they explain that I have to set the radio in either...
Hi, I am using a app_gpiote_user_register to register a gpiote user and then enabling it, before I set the pins this user detect to be input using nrf_gpio_cfg_input. When...
Using eclipse and code sorcery compiler I got an undefined label error, see below
[b]_build/gcc_startup_nrf51.o: In function Reset_Handler': /home/oscar/workspace/Nordic...
Hi everyone:
use Gazell to builder multi-node .
so i have to re-enable pipe number on connect state.
my Fragment code about "open/close pipe".
but it not work correctly...
In nrf_gpiote.h:
The workaround code for PAN_028 OUTINIT anomaly (#9) will cause the GPIO to glitch to the undesired state if it is already assigned to a GPIOTE and in...
I'm trying to use the NOACK mode for some packets on the transmitter side,
and W_ACK_PAYLOAD on the receiver side.
My problem is that if the receiver gets a packet with...
Hi,
mi question is about how to configure in a good and complete way Timer1 and Timer2, so trying to be more specific with my Question:
I need timers with a Tick of 250ns...
We are creating the source program for examining RF module which uses nRF24LU1P.
It is the program that it transmits on the frequency specified from PC.
The API of USB...
