Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi,
Been using nRF51822 before but on this new design I have an external MCU running the main duties.
I've been reading up a bit on both but would like to get some thoughts...
Hi nordic engineer:
I want to know the right process to delete the bonds when the device connected.
There is a button used for bonding. When it pressing by more than...
That means, that the nRF51822 is always allowed to send, but on it's receiving side, he could slow down the opponent side by using it's Rts line?
I now, I could archive that...
Hi,
I made simple command shell via UART. It works fine when I type commands in terminal by hand. But I run into troubles when BLE chip is fed from MCU that send characters...
When I connect my ble mouse to the PC win8.1 , media button works normal.
When I power off and power on my mouse, it reconnected to win8.1 PC quickly, sensor ,left button...
I'm using the nRFgo motherboard (nRF6310 together with the PCA10004 Cpu board. I'd configured the nRF51822's Uart to 1 MBaud).
Is the RS232 level shifter (which is part of...
It's this will be work?
// Initialize the Bond Manager.
bond_init_data.flash_page_num_bond = FLASH_PAGE_BOND;
bond_init_data.flash_page_num_sys_attr = FLASH_PAGE_SYS_ATTR;...
Hello：
I need to ask you after the next programmed into how this routine testing 。（nrf51_sdk_v4_4_2_3355\nrf51822\Board\nrf6310\ble\ble_app_alert_notification ） The iphone...
Dear Developer Zone,
I am working with nRF51822 and IOS.
My device can only be connected to one central, so to one iPhone. To refuse connection from others centrals...
Hi all,
I've got some questions about the DFU OTA Nordic example (nRFToolbox):
What is available full stack update or profile update?
Firmware flow, does it need to...
Hi Folks,
I'm running into a problem with the pipes on my nRF8001. After I issue a Connect (0x0F) command, I receive:
CommandResponseEvent (0x84)
ConnectedEvent...
We have setup the RX and TX modes for ANT+ in Advanced Burst mode.
The setter function works (can confirm that by using sd_ant_adv_burst_config_set());
However when...
Hello,
I understand that S310 stack currently supports Ant+ and BLE peripheral. Is there any way to incorporate BLE central (S120) and Ant+ (S210) stacks on the same device...
Hi,
I have nexus 4 smart phone with nRF Master Control Panel application. How can i change the IO capability of the master device? I need to test the pairing process (passkey...
