Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
We have developed and certified a module which uses the nRF24l01+. We spent a good amount of time tuning the antenna circuitry which has resulted in very good range... in...
Hi,
how to get into the bootloader mode without pressing any button, when some application is running? I also tried it with setting the NRF_POWER->GPREGRET but it is not...
I am looking for a minimalistic schema design using BLE for collecting data from i2c (twi) sensor and sending them over blue-tooth to the receiver. I need the following features...
Hello,
I would like to know if there are any restrictions in the amount of external memory (RAM, Flash) that can be added to a system using a nRF51822. In that case which...
Although there are some posts dealing with bond manager issues, I have not been able to find a similar issue. I am using part of the BLE code from nRFready Desktop 2 v1.0...
Hi,
i have some trouble with acting with the nrf 51822 ADCs. My Problem is that i have an Impuls which is 100 uS long and i have to measure it with 2 ADCs. I know that...
Hi,
What will happen when we press the service discovery button in the master control panel? do we get any event like BLE_GAP_EVT_CONNECTED? I couldn't find any detail regarding...
I'm looking for information to start developing BLE slaves with nRF51822, but I can't find any datasheets/SDK. Do I need to buy the Development Kit in order to have that?...
I have an issue with my keyboard working with the windows suface (on windows 8.1). Occasionally, the last character sent is repeated several times instead of one. I do not...
On the nRF51822, I see that by programming the readback protect register, one can prevent reading code regions 0 and 1 from the SWD interface. However, if one had access to...
Hi,
I just watched a webinar from the bluetooth SIG on how to create source code from the nRFgo Studio for the nRF8001. Is the same possible for the nRF51822? To create...
Hi,
We modified the ble_app_hrs code to work with accelerometer peripheral, and we have created some custom characteristics with custom uuid's. Now we need to set the device...
Hello, Everyone:)
Nice to meet you !
Please could you commennt my first question on this community zone.
I've a question for the accuracy of synthesized clodk 32k on...
Hi
i am using NRf51822 custom board. In that i have NOR(spi0) and LED(i2c0).
But switching from spi0 to i2c0 is not possible so that i am not able to switch
off led...
Hello,
I'm using nRF51822 to implement a proprietary radio protocol. My first attempt, in the receiver, was polling the EVENTS_* registers. An example:
NRF_RADIO-...
