Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
hi guys, i am writing a TWI application along with S110 but i am not getting the proper value from the sensor which is TWI interface, is anybody wrote an application, kindly...
Hi,
We have a custom board with nrf51822 and we use chip antenna from ST BAL-NRF01D3, now the distance it support is very very short (less than 20 cm). So, please tell me...
Hello,
Can I assign two GPIOTE tasks to work with the same output port? One to set it high, another to set it low.
Here is the code segment:
nrf_gpiote_task_config...
Thanks for all your help.
From 30-yr programmer and new bit-banger.
Playing with the 6310 example, rtc_example, the following code makes no sense to us with the toggle...
I have just begun tests with the nRF51822 DK.
I have written a test program which uses the RTC and PPI to generate an event every 125 ms, and use a task to toggle a GPIO...
Hi,
I´ve programmed the nRF51822 DevKit´s module (PCA10004) with S110 SoftDevice and example <ble_app_pwr_profiling>.
In SystemOffMode I measure a current consumption of...
Hi
I trying to read data from EEPROM through i2c bus . i used twi_hw_master.c application code.
i am reading same data from EEPROM when i debug step by step. but once...
Hello,
I would like create a basic programme in c/c++ for the NRF24LU1 .
I have take sdk, when i try compiling 1 programme i have a lot of errors .
What compilator...
Hi,
I use an app_timer to gather ADCs and send with Gazell with period 5ms.
What I suffered is the sent packet is different from what I put in buffer.
my pseudo code...
I am able to send data from EK to MCP but even i am sending one byte of ASCII(alphabet) of data, it is showing as hex value in MCP ex., 'C' as 43 , if i want to see ASCII...
Hi,
How to set the advertisement parameter's (uuid's list) , while using both custom and SIG adopted services?
I modified the source code as below, but it is not showing...
I would like to implement a simple wireless sensor network, using Enhanced Shockburst with Auto-ACK. The idea is that there will be many sensor nodes (SNs) reporting to one...
I have a question about using the GPIOs,I found that I can set a ‘1’ at the same bit position of OUTSET register and OUTCLR register. But which one is effective ?
Hello guys,
Looking through the product specification for nRF8001 I am still not clear on whether a master device can be connected to the nRF8001 (in peripheral mode) and...
