Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
Hello,
I am running a nRF51822 rev G0 with Soft Device 6.0.0 & SDK 5.2.0. My device implements a custom service with 4 characteristics. One of those characteristics is...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
When the central and peripheral is connected, we can get the RSSI value through sd_ble_gap_rssi_start() function. but how can I get the RSSI value when not connected (scaning...
Update: I've worked on the BLE arduino sdk from Nordic, and followed all the directions, but I'm having some compiler errors. I've crossposted to a different forum for more...
I am using pstorage library to keep some data in NVM.
Should I use some nrf_delay calls while using pstorage_clear()?
I am calling pstorage_store from callback function...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,
From the documentation for the sd_ble_gap_sec_info_reply() function,
"This function is only used to reply to a BLE_GAP_EVT_SEC_INFO_REQUEST, calling it at other times...
Dear Madame/Sir
From my client I received nRF51822 DK.
See att file.
I do not see Product Key for DK
How can you solve the problem ?
Redards
Valeri Tosev
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
