Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I've downloaded the latest SDK and soft device. I've been able to compile the ble_app_ancs project, run it on my dev board and even connect to my iPhone. Although I'm getting...
Hi everyone
I'm using the nrf51822 connect with stm32f103 through UART,it's current is >1.9mA,is it normal?
I have full reset to disable the debug interface,it can...
Hello developers,
I've got an nrf51822 EVA kit with on it the QFAACA chip. KEIL v5.0.5, J-link V4.78, nRFGo Studio V1.16 and nrfGo SDK (zip) V4.4.2. The Softdevice on the...
when I enter the system off mode then used a GPIO to wake up the IC, the "RESETREAS" register show "Reset due to wake-up from OFF mode when wakeup is triggered from the
DETECT...
Hi,
I have only nRF51822 DK without starter kit motherboard. how can I download softdevice(S110 Bluetooth low energy stack) to my nRF51822 chip in the Keil environment?
...
Hi all,
the release note of SDK 4.3.0 reports that it was tested and verified using BLE S110 version 5.2
When it will be available (version 5.2) ?
Actually we can download...
Hi,
I want to read the data by the radio.now I have read the temperate data from the tags by 51822. the data include the ID value and the temperate value. the ID is hex ...
Hello,
I'm working with nrf51822 on a custom board and i'd like to use the LPCOMP as wakeup source. I configured the module by the code listed above:
void lpcomp_init...
So now that I understand the problem with overlapping asserted events on the GPIO port, I can't figure out the correct way to reset the sense field in the GPIOTE_IRQHandler...
Hi,
I follow steps in User Guide version 1.2. The Blinky project is working fine.
Then I program SoftDevice and after than compile and Download HRM using Kail
But led...
now,i pairing my peripheral and Communication read/write data. but have some issue for disconnect/reconnect .
1.disconnect: when i disconnect (call didDisconnectPeripheral...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
