I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
Hello,
I need to read by Battery Voltage using ADC. My Battery is 3.3v which is being stepped down to 2.1V using a LDO regulator. So my VDD is 2.1V in DC/DC mode.
Now I...
Hi guys I'm sending data from an nexys 4 fpga through an spi to my nRF51 (pca10028) I have the fpga set as the master and I'm able to read data sent to the nRF51 through my...
Hi.
I'm using nrf52 as slave for another device. I'm reading test string from the nrf buffer and I can see extra zero (rest of the content is then offset by one -> corruption...
Hi, i know this question has been ask before but, i was reading and readind and i could find a way to do it. I got the theory but when i'm going to implement it in my code...
Hi there,
i cannot get the hrs_c example to connect to a heartbelt.
The heart belt is found and a connection is established:
[APPL]: >> DM_EVT_DISCONNECTION
[APPL...
Hi
I am working on nrf52 using BMD300 RIGADO board.I am trying to run BLE UART example of nrf SDK 11.0.0.But while I am running the code I am getting errors as
: struct...
In Nordic infocenter/nRF5 SDK v11.0.0/Examples/Bluetooth low energy examples/BLE Central & Peripheral/, I found a example project which name is "Experimental: BLE LE Secure...
BLE is first initialised in my code, then SPI is initialised. If no SPI transfers are to be executed in the code, the code compiles, runs correctly and BLE functions correctly...
I have a very simple program that generates a 50% duty cycle clock using the NRF_PWM0 on the new nRF52 device. Unfortunately, my Tektronix 1GHz oscilloscope doesn't lock to...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Is there a way for firmware running on the nRF52 to detect the presence of a SEGGER (or other) SWD capable device? I've looked through all the nRF registers but couldn't find...
Hi all
Our application, built on the NRF51822 Rev. 3 and the SoftDevice S130 V1.0.0, uses the UART0 with 115'200 baud, 8N1, to communicate with another controller/PC. Hardware...
Hi, In my project I want to read data from i2c and update in advertising data and the board need to advertise without time out (i.e 24x7) for these I take advertising timeout...
