Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
Hi,
I made a own service for a rotary dail in a peripheral(S110). This service send the speed, direction and a counter (all uint8) of de rotarydail in separate characteristics...
Hi Everyone ,
We were using nrf51822 rev1 IC for our project and now it is changed to nrf51822 rev3 . Previously we were able to detect the chip in nRfgo Studio on our...
I am looking for a device with support for the 4.2, long packets (up to 255 bytes) feature. I see that the nRF52 is a 4.2 device. But for what I understand the optional long...
I am using s120 for central device, and my central device connects to multiple BLE slaves. After connection, some slaves may lost connection due to power off of that device...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hi,
My goal is to capture on gpio burst infrared proprietary "messages" composed of multiple "bits".
The Length of each bit is around 100 to 200us.
Initially I planned...
(I understand my question is similar to devzone.nordicsemi.com/.../ , but I would like some additional clarification not provided in that post.)
Hello, I've been developing...
On a BLE_GAP_EVT_CONNECTED, I'll send some data to an attached microcontroller via UART. The code will expect a response of that data, all while being inside that BLE_GAP_EVT_CONNECTED...
My application involves the Nrf52 using softdevice and a slave only SPI ADC running at approximately 26khz. The ADC has a pin interrupt to indicate data ready. There seems...
Building nrf_delay.c (or anything else including nrf_delay.h ) with NRF52 defined produces:
arm-none-eabi-gcc -I C:\Nordic\nRF5_SDK_11.0.0-2.alpha\components\device -D_DEBUG...
Hi, someone know whi when i press disconnect on iphone the nrf51 restart from the mail?!
Why if i disconnect android device the chip does not restart as the iphone?! is normal...
I'm trying to build BLE driver 0.5.0 for 64bits.
I've downloaded:
MinGW 4.8.2 64bits
boost 1.56 and compiled it using address-model=64
CMake 3.4.1
Python...
Hello Nordic community:
I've read about Serialization in the nRF51 SDK doc and would like to prototype an example with it.
I saw a notice of it being removed post 7...
Hi,
Is it possible to get a more detailed description of the GPIO block than what is available in the reference manual? Specifically i'm interested in how the disconnect...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
