My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
I've been using the ble_app_uart example as a template for our use case. It is a good starting point. We don't actually need UART functionality, and we've assigned...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
Hello.
How to write custom firmware updater, which:
Takes new firmware from other device on SPI or I2C bus.
Writes it to flash ("bank1" at 0x1B000, or...
Hi;
I'm studying on SPI communication at nRF51822 (not DK) but i could not find the pins for spi communication, i read at somewhere SPI is only used at DK(developer kits...
hi
i'm using the nrf15822 beacon for an application of communication on arduino
I just would like to understand how i should start to stream my data using the beacon beacause...
Hi all,
I am using S130 in scanning mode and I would like to list the devices that are currently advertising by their friendly name. I have access to p_ble_evt via BLE_GAP_EVT_ADV_REPORT...
Hi,
I usually use electronics.stackexchange.com/.../15143 approach for decoupling capacitors and until now I had much better EMI performances.
I make sure that tracks...
We would like to reduce the attribute table size a little to increase free RAM. Are there any guidelines explaining how we can judge how large the table needs to be for a...
I compile SDK7.2 example hrs in "experimental_s110_with_dfu" by eclipse,
and I download softdevice & bootloader by nRFgo
then i use master control panel to DFU the hex which...
