Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm trying to get the ble_app_hrs example working in Eclipse, but the stack pointer is not setup correctly. It's at the start of the RAM (0x20000000), and therefore it already...
I'm implementing an Android 4.3 app which uses an nRF51822 and the BLE proximity profile. I have the following as starting points for the app code:
The BLE sample...
I can't seem to find the required current of NVMC doing erase and write. The product spec has only timings but not more. Could someone from Nordic provide some figures? Experimental...
Hi,
I have a C# app connecting to 51822 devices, doing data/firmware download. When I try to send erase page command (before write), erase works, but there is a disconnect;...
Should we keep track of this by monitoring the write events or poll the gatts value via the softdevice?
It looks like it's faster (+shorter = less consumption) to monitor...
Over the past few months I have worked extensively on a few different projects that all utilize the nRF51422. In some recent debugging of GPIO issues (both relating to SENSE...
As the title says, I am wondering when the new SDK will be released to support the nRF51822 hardware revision. It looks like the latest (v4.4.1) doesn't have anything new...
the very similar issue
Friday, October 04 2013, 02:23
I have staerter kit + development kit. I have installed all required software and can't loat example code because...
I Every one !!! Thank for the possibility to participate in this forum.
I am trying to initialization configuration of my nRF24L01+ .
I am using CY8C3866AXI-040 from Cypress...
Hi, i'm experimenting RTC1 using the app_timer module (not using S110 soft device), and i find some problems onRTC prescaler. If i set values as stated in the datasheet, for...
Hi,
I am trying to run several applications sequentially on the nRF51822.
I have another microcontroller controlling the nRF51822 by SPI.
I init the stack, the services...
Hi, I'm just wondering if there's a reason that the example code is always initializing all structures through functions. Has it something to do with sleep mode and RAM retention...
Hello,
I have a couple of questions about sending multiple notifications:
I want to send multiple notifications (from same characteristic), is that allowed by...
Looking at the AN36 code, i notice that in the APP_SCHED_INIT define, for the argument EVENT_SIZE is used sizeof(app_timer_event_t) . In the meantime, the scheduler is used...
