Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using a code to save 4 bytes on the flash memory and it works. In, fact i checked the data address concerned using the keil and i see the changes when i write and...
I can send a CR terminated string through the UART using tx fifo OK.
BUT, if I receive a string from the UART rx OK first, and then try to send a string, only the 1st character...
Canyou please tell me how to do , to save correctly 4 bytes in my program that uses flash memory for bonfing. i have how to save 4 bytes function seperatly, and my program...
Ported the hrs_rscs relay central-peripheral app with peer mgr to custom platform with mutliple peripheral devices, and it has been working very well. The last step is to...
Hi,
I have a app that using a constantly blinking LED started at power-up, however I am having some trouble stopping the timer.. (Yes, I know it's simple.. but i still...
Dear support team,
I have problem with recovering the nrf52dk board.I check devzone.nordicsemi.com for issue, but nothing solve the problem. Board need to be recoverd...
I want to use nrf52832 to communicate with my sensors , but my three sensors should use spis to communicate, the others use TWI ,so in sampling , I need to switch between...
Is there a schedule to release an up to date version of the "nrf51-ble-driver_win_0.5.0" package, including the compiled serialization dll?
The package is a download for...
Hi,
I am burning the same code on two sets of chips nrf51882 and nrf51442. The nrf51882 chip is with 16kb RAM and 128kb of flash memory while the nrf51442 chip is with...
Hi,
I took a example (ble Peripheral : ble_app_uart) and enabled bonding and whitelist as per the tutorial devzone.nordicsemi.com/.../ and followed these link ( devzone.nordicsemi...
Hi. I'm using SDK 11, SD s130, gcc, nRF51822. My application is a peripheral that advertises OK and gets a connection from our mobile app OK, but then gets a PM_EVT_ERROR_UNEXPECTED...
Hi ,
I have designed a beacon using nrf51422 nordic chip. But when I checked the antenna frequency , i came to know that its above 2.45 Ghz. I tried by the changing the...
Hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\nrf52-ble-tutorial-service.uvprojx and compike then find...
hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\ nrf52-ble-tutorial-service.uvprojx, and compile ,the result...
Hello,
I am developing custom driver for TWIM. I am facing a problem with DNACK and ANACK which hangs my application. SCL and SDA lines are monitored through Saleale logic...
