Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
All,
Can anyone tell me what is the fastest time that a ble SD (5.x / 6.x) running on an nRF51 can (re)start advertising from a disconnect. Basically looking to do an ...
I am not able to connect Garmin Edge or SimulANT to nRF51-DK. Neither sensor nor receiver seems to work. Just looks like there is no RF.
Examples tried:
power_only_sensor...
Dear Sir,
Here I test the ble_peripheral example "ble_app_uart" (Softdevice 8.0) with Kail MDK ARM 5.20 environemt on the PAC10028A board.
I found it's not stable and...
Hi,
I'm having trouble increasing frequency of data TX using ble_app_hrs example on PCA10028.
I tried to increase the TX frequency of heartrate data to 100ms by configuring...
It seems that the nRF52 Development Kit mis-handles extended hex records. If it has type "04" records (extended linear address), it works OK, but if it has type "02" records...
We have an optical measurement system where we need to pulse LED and sample a phototransistor precisely during the LED pulse. The rate of sampling is 1 kHz and we plan to...
HI i need help in sending a data value of 700+ continuously
1)May i know how should i format my data packet to suit the current 20 bytes of data sent through BLE
2)Is...
Hi,
I am working on application in which I want to send 1000 or more samples using SAADC and BLE over standard master control panel APP of Nordic. For sampling analog data...
I'm trying to fully understand how DFU works and am going through the nRF5 SDK v11.0.0 example bootloader ( dfu_dual_bank_ble_s132_pca10040 ) and app ( ble_app_hrs_s132_with_dfu_pca10040...
[summary]
When I update app by Keil μVision, RAM setting is reflected correctly, but when I update app on OTA, RAM setting change is not reflected.
[condition]
Old...
Im trying to read flash memory ( N25Q032 ) identifier using SPI (NRF52) but then eveytime I try to read a register, the output is always zero, I tested with oscilloscope and...
Hi,
I'm using the nRF Dongle for sniffing.
Apparently there are many problems with the sniffer application.
First of all, the CTRL+R command for downloading the FW...
Hi!
I am trying to modify the ble_app_gls example from the 8.0.0 SDK and am running into some issues. I am trying to add the nus service to this example and would like...
