Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I'm trying to set up an iOS app (which I know is working properly) with a nRF8001 using nRFGo studio. I do not have the nRFGo dev kit (only the 8001 dev kit) so I hooked...
Hi
How to set device address in nRF8001?
I only see get device address command.
Does it mean I just only put my device address in MCU?
Thanks.
BR
Atlas
Hi,
I'm trying to generate some time variant values for testing purposes... rand() always returns 1447534768! This is in the proximity app FWIW.
So, I thought I would...
nrf24le1 memory map shows that there are two sram block size of 512byte ,the first one is data retentive (address 0-0x0200) ,another one is data non retentive (address 0x0200...
My device use the firmware program ble_app_uart to connect the nexus 7 which Installs the nRF UART 2.0 for Android 4.3 。The first connection is ok，and Data sent and received...
Hello,
I am a beginner in the world of bluetooth and bluetooth smart connections. I am working with an nrf51822 Evaluation kit an android phone (Nexus 4 running 4.4.2)...
Is it normal that after cutting SB8 our chip is still working when connected to USB port? (in case of battery we need to connect pin 1 and 2 from P1). I spend long time looking...
I have a custom board that uses the nrf51822. I have been using the sample application ble_app_uart with only one minor change, I use the internal clock (NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION...
I'm wondering when my firmware changes over time what will happen with information stored with pstorage? For example if I my new firmware release adds an additional pstorage_register...
If I have persistent data that will be updated semi-frequently, will pstorage wear out the flash memory? What steps should I take to be sure my data storage will remain functional...
Hello,
I tested nRF51822 with ble_app_hids_keyboard example, i found it cannot pair with more than one devices.
Procedures:
Pair PCA10001 with iPhone#1, it can...
Hello.
I have a nrf51822 ek and trying to create my software using same technics as the bootloader example from sdk. But sdk's bootloader in my case doesn't work. I programm...
hello all:
I have compile successfully my project.but have link trouble about my project codes for the nRF51822 with the Keil MDK-ARM toolchain (v4.6).
For example, for...
